Mode d'emploi ICOM IC-M36

[. . . ] INSTRUCTION MANUAL VHF MARINE TRANSCEIVER iM36 This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio W ARN ING is NOT intended for use by the “General Population” in an uncontrolled environment. [. . . ] q  ush [VOL/SQL MONI] once to enter the volume adjustP ment mode, then adjust the volume level with [Y]/[Z]. • “VOL” indicator starts blinking. •  he transceiver has 31 volume levels and OFF. T •  ith no key operation is performed for 5 sec. , the transceiver W returns to the normal condition. e  ush and hold [16 9] again for P 3 sec. (until a long beep changes to 2 short beeps) to enter the call channel programming mode. •  hannel number starts blinking. C w  ush [VOL/SQL MONI] twice to exit the volume adjustP ment mode. Indicates the volume level. Blinks while adjusting the volume level. r  ush [Y]/[Z] to select the desired P channel. t  ush [16 9] to program the disP played channel as the call channel. •  he channel number stops blinking. T 11 4 BASIC OPERATION ■ Volume loud function The volume loud function can be activated temporarily by pushing [LOUD MUTE]. The function does not work when the volume level is 31. q  ush [LOUD MUTE] to activate the volume loud function. P • The volume level is set to the maximum level (level 31). •  he bars of the volume level indicator appears in ascending T order repeatedly. ■ Adjusting the squelch level The squelch level can be adjusted with [VOL/SQL MONI] and [Y]/[Z]. In order to receive signals properly, as well as for the scan to function effectively, the squelch must be adjusted to the proper level. q  ush [VOL/SQL MONI] twice to enter the squelch adjustP ment mode, then adjust the squelch level with [Y]/[Z]. • “SQL” indicator starts blinking. •  he transceiver has 11 squelch levels: OP is completely open; T 10 is tight squelch; 1 is loose squelch. •  ith no key operation is performed for 5 sec. , the transceiver W returns to the normal condition. w  ush [LOUD MUTE] again, or push [VOL/SQL MONI] to P turn the volume loud function OFF. ■ Volume mute function The volume mute function can be activated temporarily by pushing and holding [LOUD MUTE]. The function does not work when the volume level is OFF. to activate the P volume mute function. • The volume level is set to the minimum level (OFF). • The volume level indicator blinks. w  ush [VOL/SQL MONI] again to exit the squelch adjustP ment mode. Indicates the squelch level. Blinks while adjusting the squelch level. w  ush [LOUD MUTE] again, or push [VOL/SQL MONI] to P turn the volume mute function OFF. 12 BASIC OPERATION 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ Lock function This function electronically locks all keys (except for [PTT], [VOL/SQL MONI], [LOUD MUTE], [Hi/Lo ] and [Y]/[Z]*) to prevent accidental channel changes and function access. * In the volume or squelch adjustment mode only. ➥  ush and hold [Hi/Lo P ] for 1 sec. [. . . ] • A n optional external speaker-micro- •  isconnect the microphone. •  he sub-microphone is covered with •  ake sure the sub-microphone is not p. T •  et the squelch level to the desired level. 12 S The noise detection function does not work. [. . . ]