Mode d'emploi SAUTER 1831MP

[. . . ] Visit our website www. sauter-electromenager. com where you will find all of our products, as well as useful and complementary information. SAUTER We cook so well together As part of our commitment to constantly improving our products, we reserve the right to make changes to them based on technical advances to their technical and functional features and appearance. Warning: Before installing and using your appliance, please carefully read this Guide to Installation and Use, which will allow you to quickly familiarise yourself with its operation. 2 99642011_A. qxp 27/03/2007 17:04 Page 3 TABLE OF CONTENTS EN 1 / NOTICES TO THE USER · Safety Recommendations ___________________________________ · Environment ______________________________________________ 2 / INSTALLING YOUR APPLIANCE · Choice of location __________________________________________ · Building in ________________________________________________ · Electrical connection _______________________________________ · Changing the power cable ___________________________________ 3 / DESCRIPTION OF YOUR APPLIANCE · Introduction to your oven ____________________________________ · Description of the accessories _______________________________ · Description of your programmer ______________________________ 4 / USING YOUR APPLIANCE · Using the programmer ______________________________________ º How to set the time _____________________________________ º How to change the time _________________________________ º Immediate cooking _____________________________________ º Programmed cooking ___________________________________ º Using the timer function _________________________________ º Display brightness______________________________________ 5 / OVEN COOKING MODES_______________________________________ 6 / CARING FOR AND CLEANING YOUR APPLIANCE · Cleaning the outer surfaces __________________________________ · Changing the catalytic walls _________________________________ 7 / TROUBLESHOOTING __________________________________________ · Changing the bulb _________________________________________ 04 05 06 06 07 08 09 10 11 12 12 12 13 14 16 16 17 19 21 22 23 3 99642011_A. qxp 27/03/2007 17:04 Page 4 EN 1 / NOTICES TO THE USER Warning Keep this user guide with your appliance. If the appliance is ever sold or transferred to another person, ensure that the new owner receives the user guide. Please become familiar with these recommendations before installing and using your oven. They were written for your safety and the safety of others. -- When in use, the appliance becomes hot. [. . . ] If the electrical installation at your residence requires any changes in order to hook up your Appliance, call upon a professional electrician. If the oven malfunctions in any way, unplug the appliance or remove the fuse corresponding to the sector there the oven is hooked up. · CHANGING THE POWER CORD -- The power cable (H05 RR-F, H05 RN-F ou H05 VV-F) must be of sufficient length to be connected to the build-in oven while it sits on the floor in front of the cabinet. To do this the appliance must be disconnected from the electrical network: -- Open the inspection flap located at the lower right of the back cover by unscrewing the two screws, then pivot the inspection flap. -- Strip 12 mm along each wire of the new power cable. -- Carefully twist together the strands. -- Loosen the screws from the terminal board and remove the power cord to be replaced. · Introduce the power cable through the side of the cover in the cable clip located to the right of the terminal board. -- All the strands of the electricity wires must be captured under the screws. -- The green-yellow coloured ground wire should be connected to the terminal . -- The neutral conductor (blue) on the N terminal. -- Screw down tightly the screws on the terminal board and check the connection by pulling on each wire. The end of cooking time display stops flashing. After these three steps, the oven heating is delayed so that cooking ends at 13:00. fig. 3 At the end of cooking (end of programmed time), - The oven stops, - The cooking time indicator and 0:00 flash (fig. 3). - A series of beeps is emitted for a few minutes. The beeps are definitively stopped by pushing on any touch control. The displays once again shows the time of day when the function selector is returned to 0 (fig. 4). fig. 2 fig. 1 fig. 4 15 99642011_A. qxp 27/03/2007 17:04 Page 16 EN 4 / USING YOUR APPLIANCE · USING THE TIMER FUNCTION - Your oven's programmer can be used as an independent timer that allows you to count down a time without operating the oven. In this case, the timer display has priority over the clock display. - Press the " " TOUCH CONTROL (fig. 1) until the timer symbol flashes -> 0. 00 and a small hourglass flashes. - Adjust the selected time by pressing the + or touch controls. - Press on the " " touch control to confirm or wait a few seconds. [. . . ] Slide the drip tray onto the lower shelf support to collect greases. · Recommended for grilling chops, sausages, slices of bread, prawns placed on the grid. * Programme(s) used to obtain the results indicated on the energy label in compliance with European standard EN 50304 and in accordance with European Directive 2002/40/CE. 18 99642011_A. qxp 27/03/2007 17:04 Page 19 6 / CARING FOR AND CLEANING YOUR APPLIANCE EN · CLEANING THE OUTER SURFACES To clean the window of the electronic timer, as well as the oven door, use a soft cloth moistened with a glass cleaner. Do not use abrasive cleaning products or hard, metallic scrubbers to clean the oven's glass door, which could scratch the surface and cause the glass to shatter. To preserve your appliance, we recommend that you use Clearit cleaning products. Professional expertise serving individuals Clearit offers you professional products and solutions designed for the daily care of your household appliances and kitchens. [. . . ]