Mode d'emploi TRENDNET TPL-401E2K QUICK INSTALLATION GUIDE

[. . . ] TRENDnet TPL-303E, TPL-304E, TPL-401E, TPL-310AP, ou autre TPL-401E) (Remarque : Ceci ne vaut que pour le TPL-401E. Le TPL-401E2K comprend déjà deux TPL-401E adapter) Exigences logicielles SE supportés Windows 7 (32/64-bit) Windows Vista (32/64-bit) Windows XP (32/64-bit) Microprocesseur 1GHz ou superieur 800MHz ou superieur 300MHz ou superieur Memoire 1GB RAM ou superieur 512MB RAM ou superieur 256MB RAM ou superieur Remarque: L'utilitaire de configuration vous permettra d'améliorer la sécurité de votre réseau powerline en vous donnant la possibilité de changer le nom par défaut du réseau et de créer votre propre nom de réseau à votre réseau powerline. L'utilitaire peut aussi vous aider à réparer les problèmes de connectivité entre les adaptateurs powerline en vérifiant le nom du réseau. Veuillez consulter le Guide de l'utilisateur sur le CD-ROM du TPL-401E pour découvrir les instructions d'installation et d'utilisation. 1 2. [. . . ] Note: 1. DO NOT install the TPL-401E until instructed to do so. 2. DO NOT plug the TPL-401E into a surge protector or power strip. Avoid connecting the TPL-401E into an outlet that has appliances (e. g. refrigerators, washer and dryer) plugged in. 4. In order for the TPL-401E adapters to link to each other, each unit must be on the same electrical system. 5. A maximum of 16 TPL-401E adapters can be networked. 6. Assuming that the TPL-401E adapters are configured with the default settings, to create a powerline network, simply connect all TPL-401E adapters to wall outlets that are on the same electrical system. No additional configuration in the utility is necessary. 7. The network name must be the same on all powerline adapters in order to establish connectivity. If the network name is not the same on all powerline adapters, the adapters will NOT establish connectivity. The default network name for the TPL-401E is "HomePlugAV " 7 Below is an example showing how to create a Powerline network using the TPL-401E and your existing router to share Internet. 1. Plug a TPL-401E into an available power outlet. This TPL-401E should be located within the reach of the router's network cable. Outlet 2. Connect a network cable from the TPL-401E to an available LAN network port on your router (e. g. Plug a second TPL-401E into an available power outlet where your remote computer or network appliances (e. g. Game Console, IP Set box, network enabled TV, etc. ) are located. Outlet 8 4. Connect a network cable from the TPL-401E network port into the network port on your remote computer or network appliance (e. g. Game Console, Blu-ray player, IP Set box, network enabled TV, etc. ). Outlet 5. Verify that the PWR (Power), PL (Powerline) and ETH (Ethernet Link/ACT) LEDs are on for both TPL-401E adapters. Your installation is now complete For detailed information regarding the the TPL-401E/TPL-401E2K, configuration and advanced settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or TRENDnet's website at http://www. trendnet. com. Register Your Product To ensure the highest level of customer service and support, please take a moment to register your product Online at: www. trendnet. com/register Thank you for choosing TRENDnet 9 3. LEDs and Buttons PWR (Power) ETH (Ethernet Link/ACT) PL (Powerline) The Gigabit Ethernet/Network Port and Reset buttton are located at the bottom of the device. Gigabit + Ethernet / Network Port Reset Button Sync Note: Please refer to the User's Guide on the TPL-401E/TPL-401E2K's User's Guide CD for detailed explanations of each LED and button. 10 Dépannage 1. J'ai vérifié si mon périphérique Powerline était branché à mon poste de travail, mais je n'arrive pas à détecter d'autres périphériques Powerline. 1. Vérifiez que vous utilisez les câbles de réseau Ethernet Cat. [. . . ] Then click on Obtain an IP address automatically. 4. I have a HomePlug 1. 0 or HomePlug Turbo network. The TPL-401E is not backwards compatible with HomePlug 1. 0 or HomePlug Turbo. Do I need to reconfigure my TPL-401E after I hit the reset button? [. . . ]