Mode d'emploi ASUS EEE PC 1015T

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Use this menu to enable and make changes to the advanced features. Use this menu to set a password to control bootup and control access to the BIOS setup menu. Use this menu to configure and enable Power Management features. Use this menu to configure the default system device used to locate and load the Operating System. Use this menu to exit the current menu or specify how to exit the Setup program. To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted. 32 Notebook PC User's Manual BIOS Setup Program (Cont') Legend Bar At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding alternates and functions. LEGEND KEY ALTERNATE F1 Esc or Tab Shift + Tab - (minus key) + (plus key) Home End F9 F10 Alt + H Alt + X keypad arrow keypad arrow keypad arrows Enter (none) F5 F6, spacebar PgUp PgDn (none) (none) FUNCTION DESCRIPTION Displays the General Help screen from anywhere in the BIOS Setup Jumps to the Exit menu or returns to the main menu from a sub-menu Selects the menu item to the left Selects the menu item to the right Moves the cursor up and down between fields Moves the cursor to the next position available in the field. If there is only one field, the Tab key will move the highlight down to the next field Moves the cursor to previous position available in the field. If there is only one field, the Tab+Shift keys will move the highlight up to the previous field Scrolls backward through the values for the highlighted field Scrolls forward through the values for the highlighted field Moves the cursor to the first field Moves the cursor to the last field Sets current menu items to default values Saves changes and exits Setup Sub-Menus Note that a right pointer symbol appears to the left of certain fields. This pointer indicates that a sub-menu can be launched from this field. A sub-menu contains additional options for a field parameter. You do not need to make changes to this field. This is a display only field. Extended Memory This field displays the amount of extended memory detected by the system during bootup. You do not need to make changes to this field. This is a display only field. Notebook PC User's Manual 35 Main Sub-Menu IDE Primary Master This field is used to configure the IDE Hard Disk installed in the system. To configure a hard disk drive, move the cursor to highlight the IDE Primary Master field and press the Enter key to enter the sub-menu. Main Advanced PhoenixBIOS Setup Utility Security Power Boot [3242MB] Exit Item Specific Help IDE Primary Master Type: Cylinders: Heads Sectors: Maximum Capacity: Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: [Auto] [ 6282] [ 16] [63] 3242MB [16 Sectors] [Enabled] [Enabled] [Fast PIO 4] [Disabled] Auto = autotypes hard-disk drive installed here. CD-ROM = a CD-ROM drive is installed here. User = you enter parameters of hard-disk drive installed at this connection. IV. BIOS Software F1 Help Esc Exit Select Item Select Menu Enter Change Values Select Sub-Menu F9 Setup Defaults F10 Save and Exit NOTE!Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of the drive. Incorrect settings may cause your system to not recognize the installed hard disk. To allow the BIOS to detect the drive type automatically, select [AUTO]. 36 Notebook PC User's Manual Main Sub-Menu (Cont') Type Select Auto to automatically detect an IDE type drive. [. . . ] The Notebook PC enters Suspend when the system remains idle for a specified amount of time. The timeout setting of both Hard Disk and Video can be set by the BIOS Setup. To resume system operation, press any key. The Power LED will blink when the Notebook PC is in either one of the power saving modes. Standby Mode V. [. . . ]