Mode d'emploi DAIKIN SKYAIR ALPHA

[. . . ] No express or implied warranty is given for the completeness, accuracy, reliability or fitness for particular purpose of its content and the products and services presented therein. [. . . ] As described in below procedure, the content of retry can again be consulted in Monitor mode: Setting item 2= latest retry Setting item 3= 1 cycle before Setting item 4= 2 cycles before To enter "Monitor mode", press the MODE (BS1) button when in "Setting mode 1". Super long Disabled (factory setting) No display 60 min NO COMPENSATION (Temperature [A] °C which an air conditioner controls when the temperature of a remote controller is A °C) OFF Slightly up Prohibition Low Option Higher priority on the air temperature -2°C Set-speed Enabled (factory setting) Set-speed (factory setting) Slightly up 3-way flow — Normal (factory setting) About 2500 hrs (factory setting) Non display: - airconditioning operation, Display: - filter auto cleaning (factory setting) 03 — — — — — — 04 — — — — 0, , , , 0 — 05 — — — — — — 11 (21) 2 3 4 6 (note 5) Fan OFF at Thermostat OFF Airflow rate setting during heating Automatic operation mode control Sensitivity of presence sensor Option (KRP1B*) output Compensation of temperature around human body Compensation of floor temperature Fan speed heating thermostat OFF Automatic restart after power failure reset Fan speed cooling thermostat OFF High air outlet velocity (for high ceiling applications) Selection of airflow direction Flap moving in the swing mode Airflow range setting The largest time interval for Dust Collection Sign Display for "self cleaning decoration panel" Display or non-display of green lamp on the selfcleaning decoration panel Normal (factory setting) Standard (factory setting) Available (factory setting) High Compressor (factory setting) Floor sensor does not work -4°C LL-speed (factory setting) Disabled LL-speed Standard (factory setting) 4-way flow (factory setting) All 4 flaps synchronized Upper About 1250 hrs (dusty place) Display both: - airconditioning operation, - filter auto cleaning — Up — Standard (factory setting) Operation Standard (factory setting) ±0°C (factory setting) — — — Up — Two opposite flaps synchronized (factory setting) Lower About 5000 hrs (less dusty place) Display: - airconditioning operation, Non display: - filter auto cleaning — — — — — — — Sensor does not work Malfunction Higher priority on the floor temperature +2°C — — — — — — — — — — — — — — — — — — — — — — — — — 11 (22) 0 7 (note 5) 8 (note 5) 12 (22) 3 5 6 13 (23) 0 1 2 4 14 (24) 2 4 8 9 15 (25) 1b (2b) 5 14 Auto control operation for Filter Auto Cleaning Filter cleaning time for "selfcleaning decoration panel" Individual setting of ventilation Wind block (note 6) enable / disable setting Auto control operation Normal place in terms of dust (Normal office) (factory setting) Normal (factory setting) Enable (factory setting) Not auto control operation (factory setting) In case of dusty place Individual operation — — — — — — — — Disable INFORMATION 1. 2 Field Setting for Outdoor Unit Setting by BS Buttons With “Setting mode 1”, “Setting mode 2” and “Monitor mode”, various settings and data can be checked. Setting mode 1 The initial status (normal operation) is “Setting mode 1”, This mode indicates operating status - “TEST (test operation)”, “HWL (error)”, “L. Monitor mode This mode indicates “oil return operation”, “outdoor unit class”, “contents of retry”, “contents of error”, “causes of stepping-down operation”, etc. Press the BS1 (MODE button) one time Monitor mode Setting mode 2 On H1P H1P Off H1P Blinking Setting Mode 1 In this mode, the following conditions can be checked: 22/08/16 | Version 1. [. . . ] H: OFF l: BLINK k: ON Operating procedure Press the MODE (BS1) button of “Setting mode 1" for 5 seconds or more and set to “Setting mode 2”. [. . . ]