Mode d'emploi DENON POA-F100

[. . . ] RS-232C Connector type: DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4, 6, 7, 8, 9pin : NC ) Communication format: Synchronous system : Tone step synchronization Communication system : A half duplex Communication speed : 9600bps Character length : 8 bits Parity control : None Start bit : 1 bit Stop bit : 1 bit Communication procedure : Non procedural Communication data length : 135 bytes (maximum) -1- Protocol specification The following three data forms are defined. [. . . ] EVENT : The message sent to a controller (Touch Panel etc. ) from a system (POA) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT. RESPONSE : The message sent to a controller (Touch Panel etc. ) from a system (POA) if the `request command' (COMMAND+?+CR(0x0D)) has came from a controller. AMPL12NRM AMPL12BAP AMPL12BTL AMPL34NRM AMPL34BAP AMPL34BTL AMPLR5NRM AMPLR5BAP AMPLR5BTL AMPR12NRM AMPR12BAP AMPR12BTL AMPR34NRM AMPR34BAP AMPR34BTL AMP?AMPR34? function Return Channel setting Return Channel L* setting Return Channel R* setting L1/L2 Power Amp setting L3/L4 Power Amp setting L5/R5 Power Amp setting R1/R2 Power Amp setting R3/R4 Power Amp setting Return Power Amp setting Return * Power Amp setting Example PAIN?<CR> PAINL1?<CR> PAINL2?<CR> PAINL3?<CR> PAINL4?<CR> PAINL5?<CR> PAINR1?<CR> PAINR2?<CR> PAINR3?<CR> PAINR4?<CR> PAINR5?<CR> PAAMPL12NRM<CR> PAAMPL12BAP<CR> PAAMPL12BTL<CR> PAAMPL34NRM<CR> PAAMPL34BAP<CR> PAAMPL34BTL<CR> PAAMPLR5NRM<CR> PAAMPLR5BAP<CR> PAAMPLR5BTL<CR> PAAMPR12NRM<CR> PAAMPR12BAP<CR> PAAMPR12BTL<CR> PAAMPR34NRM<CR> PAAMPR34BAP<CR> PAAMPR34BTL<CR> PAAMP?<CR> PAAMPL12?<CR> PAAMPL34?<CR> PAAMPLR5?<CR> PAAMPR12?<CR> PAAMPR34?<CR> -4- PAIN?<CR> RESPONSE becomes the following order. State of input channel L1 ­State of L2 -> State of L3 -> State of L4 -> State of L5 -> State of R5 -> State of R4 -> State of R3 -> State of R2 -> State of R1 PAINL1xxx<CR> PAINL2xxx<CR>PAINL3xxx<CR>PAINL4xxx<CR>PAINL5xxx<CR> PAINR5xxx<CR>PAINR4xxx<CR>PAINR3xxx<CR>PAINR2xxx<CR>PAINR1xxx<CR> (xxx ; "OFF" or "RCA" or "XLR") RESPONSE becomes the following order. State of Power AMP channel L1/L2 -> State of L3/L4 -> State of L5/R5 -> State of R4/R3 -> State of R2/R1 PAAMPL12xxx<CR> PAAMPL34xxx<CR>PAAMPLR5xxx<CR>PAAMPR34xxx<CR>PAAMPR12xxx<CR> (xxx ; "NRM" or "BAP" or "BTL") PAAMP?<CR> -5- COMMAND PA PARAMETER MTON MTOFF MTLCHG MTCCHG MTRCHG MT? [. . . ] MTR? function Meter setting on Meter setting off Left Meter setting Center Meter setting Right Meter setting Return Meter setting Return Meter On/Off setting Return Left Meter setting Return Center Meter setting Return Right Meter setting Example PAMTON<CR> PAMTOFF<CR> PAMTLCHG<CR> PAMTCCHG<CR> PAMTRCHG<CR> PAMT?<CR> PAMTO?<CR> PAMTL?<CR> PAMTC?<CR> PAMTR?<CR> PAMT?<CR> RESPONSE becomes the following order. [. . . ]