Mode d'emploi FUJIFILM INSTAX SQUARE SQ6

[. . . ] JP EN 使用説明書/困ったときには/安全にご使用いただくために User’s Guide/Trouble shooting/Safety precautions CPL11B704-101 日本語: 3ページから22ページをご覧ください。 ENGLISH: See pages 25 to 46. © 2018 FUJIFILM Corporation. All rights reserved. 日本語 目次 各部の名称. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . ス トラップを取り付ける. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . 電池を入れる. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 . [. . . ] (No other films can be used. ) 2 Match the yellow line on the film pack with the yellow positioning mark in your camera. Follow the FUJIFILM Instant Film “instax SQUARE” instructions. ● Replace both batteries with new batteries and load the film pack again. The LED(s) on the mode indicator is flashing. The film pack won’t load into your camera, or won’t load into your camera smoothly. The film cover cannot be ejected. 1 The film pack is not for your camera. 2 You are not loading the film pack correctly. ● The battery power is low. 39 Problems The film cannot be ejected. Possible Causes 1 The camera shakes or has been dropped and the film is misaligned. ● The batteries are not the same type. Solutions 1 Load a new film pack. 2 Remove both batteries and insert them again. If this does not solve the problem, remove the jammed film and load a new film pack. ● Replace both batteries with new CR2 lithium batteries of the same brand/type. The battery becomes exhausted quickly. Printed pictures EN Problems Part or whole finished print is white. (White in color) Possible Causes ● The back cover was opened before you have used up the film. 1 The ambient temperature is low (below +5°C/+41°F). 2 The AE light sensor window or flash sensor window was covered. 1 The ambient temperature is high (above +40°C/+104°F). 2 The picture was taken facing the light. 3 The flash lampface, AE light sensor window or flash sensor window was covered. 4 The background is too bright in comparison with the subject. 5 The flash light did not reach the subject. 6 The flash light reflected back from a mirror or window glass. Solutions ● Do not open the back cover until you have used up the film; otherwise, the rest of the film may be exposed and ruined for use. 1 Before taking pictures, place your camera in a warm place to bring it to room temperature. 2 Be careful not to block the AE light sensor or flash sensor window, or so that nothing blocks it. [. . . ] 3 When using a tripod, check the strength of the tripod and then mount the camera by turning the tripod instead of the camera body. When mounting the camera to a tripod, be sure not to turn the tripod screw excessively, apply unreasonable force, etc. Also, do not carry the camera while it is mounted to the tripod. Personal injury or camera damage may result. [. . . ]