Mode d'emploi PANASONIC CS-TE35TKEW

[. . . ] Order No: PAPAMY1703052CE Indoor Unit CS-TE20TKEW CS-TE25TKEW CS-TE35TKEW CS-TE42TKEW Outdoor Unit CU-TE20TKE CU-TE25TKE CU-TE35TKE CU-TE42TKE Destination Europe Turkey Please file and use this manual together with the service manual for Model No. CU-2E12SBE, CU-2E15SBE, CU-2E18SBE, CU-3E18PBE, CU-3E23SBE, CU-4E23PBE, CU-4E27PBE, CU-5E34PBE, CU-2RE15SBE, CU-2RE18SBE, CU-3RE18SBE, Order No. PAPAMY1601016CE, PAPAMY1601015CE, PAPAMY1301048CE, PAPAMY1303046CE. WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. [. . . ] o If -2°C ≤ indoor intake temperature - remote control setting temperature < 3°C, maintain with previous mode. o If indoor intake temperature - remote control setting temperature < -2°C, HEAT mode is decided. Maintain current mode Cool /Dry Heat -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 12. 2 Indoor Fan Motor Operation 12. 2. 1 Basic Rotation Speed (rpm) A. Manual Fan Speed [Cooling, Dry]  Fan motor’s number of rotation is determined according to remote control setting. Remote control Tab ○ Hi ○ Me ○ Me○ Lo ○ QLo [Heating]  Fan motor’s number of rotation is determined according to remote control setting. Remote control Tab ○ SHi ○ Me ○ Me○ Lo ○ QLo ii Auto Fan Speed [Cooling, Dry]  According to room temperature and setting temperature, indoor fan speed is determined automatically.  When set temperature is not achieved, the indoor fan will operate according to pattern below. Fan Speed Higher Medium Lower a b c d e f g [1 pattern : 10 s] h a b  When set temperature achieved, the indoor fan speed will be fixed. When thermostat off, the fan stop periodically. 49 AMP Air Conditioning www. ampair. co. uk | sales@ampair. co. uk [Heating]  According to indoor pipe temperature, automatic heating fan speed is determined as follows. RPM Increased 39oC RPM Maintain 35oC RPM Reduced 19oC OFF Indoor Pipe Temp. Feedback control  Immediately after the fan motor started, feedback control is performed once every second.  During fan motor on, if fan motor feedback ≥ 2550 rpm or < 50 rpm continue for 10 seconds, then fan motor error counter increase, fan motor is then stop and restart. If the fan motor counter becomes 7 times, then H19 - fan motor error is detected. Operation stops and cannot on back. 12. 3 Outdoor Fan Motor Operation Outdoor fan motor is operated with one fan speed only. It starts when compressor starts operation and it stops 30 seconds after compressor stops operation. ON Compressor: ON Outdoor Fan: 30 sec ON OFF Fan Speed OFF ON  During cooling operation, and outdoor ambient temperature is below 8°C, outdoor fan speed will be controlled according to outdoor piping temperature as following: OD Pipe Temperature A B 26°C 33°C  During above condition, when indoor heat exchanger temperature is below 5°C, the outdoor fan will stop according to outdoor piping temperature as following: 50 AMP Air Conditioning www. ampair. co. uk | sales@ampair. co. uk 12. 4 Airflow Direction   There are two types of airflow, vertical airflow (directed by horizontal vane) and horizontal airflow (directed by vertical vanes). Control of airflow direction can be automatic (angles of direction is determined by operation mode, heat exchanger temperature and intake air temperature) and manual (angles of direction can be adjusted using remote control). 12. 4. 1 Vertical Airflow Operation Mode Cooling Soft Dry Airflow Direction Auto Manual Auto Manual A Heating Auto Manual B C 8 12 10 15 10 15 Inner Vane Angle (°) 1 2 3 10 ~ 45 20 10 ~ 45 20 10 30 20 20 40 50 28 36 30 45 20 32 30 45 20 32 4 5 1 Outer Vane Angle (°) 2 3 20 ~ 56 44 20 ~ 56 44 20 65 44 44 65 72 50 56 50 56 4 5 1 2 Automatic vertical airflow direction can be set using remote control; the vane swings up and down within the angles as stated above. For heating mode operation, the angle of the vane depends on the indoor heat exchanger temperature as Figure 1 below. It does not swing during fan motor stop. When the air conditioner is stopped using remote control, the vane will shift to close position. Manual vertical airflow direction can be set using remote control; the angles of the vane are as stated above and the positions of the vane are as Figure 2 below. When the air conditioner is stopped using remote control, the vane will shift to close position. Side View (Inner Vane) Reference point Step 1 110º Step 2 Stopper Step 3 Closed Position Step 4 Step 5 51 AMP Air Conditioning www. ampair. co. uk | sales@ampair. co. uk Side View (Outer Vane) Closed Position Stopper Reference point Step 1 135º Step 2 Step 3 Step 4 Step 5 Figure 2 * The horizontal vane angle tolerance is within +/- 5 degree. 12. 4. 2  Horizontal Airflow The horizontal airflow direction louver can be adjusted manually by hand. 12. 5 Timer Control   There are 2 sets of ON and OFF timer available to turn the unit ON or OFF at different preset time. If more than one timer had been set, the upcoming timer will be displayed and will activate in sequence. 12. 5. 1    ON Timer Control ON timer 1 and ON timer 2 can be set using remote control, the unit with timer set will start operate earlier than the setting time. This is to provide a comfortable environment when reaching the set ON time. 60 minutes before the set time, indoor (at fan speed of Lo-) and outdoor fan motor start operate for 30 seconds to determine the indoor intake air temperature and outdoor air temperature in order to judge the operation starting time. From the above judgment, the decided operation will start operate earlier than the set time as shown below. Indoor intake air temperature (oC) 15 min 30 10 min 25 5 min 30 35 (oC) Outdoor air temperature (oC) 5 35 min 0 5 (oC) Outdoor air temperature (oC) 15 30 min Indoor intake air temperature (oC) 25 min Cooling/Soft Dry Heating 12. 5. 2 OFF Timer Control OFF timer 1 and OFF timer 2 can be set using remote control, the unit with timer set will stop operate at set time. 52 AMP Air Conditioning www. ampair. co. uk | sales@ampair. co. uk 12. 6 Sleep Mode Operation SLEEP To maximise comfort while sleeping (CANCEL)      This operation provides you with a comfortable environment while sleeping. It will automatically adjust the sleep pattern temperature during the activation period. [. . . ] 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 2 1 1 1 1 1 1 1 1 1 1 1 2 3 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 CS-TE42TKEW ACXD50C00440 L6CBYYYL0195 CWH02C1159 CWH551146 CWH64K1010 ACXB30C02740 CWT251030 CWT251032 CWD933857A ACXH10-00870 ACXA28C00260 ACXD93-02450 ACXA73C12170 ACXA73-06360 ACXD93-02460 CWA50C2664 ACXE20C00850 ACXE24-00590 ACXE26-00250 ACXH62-00120 CWH521259 CWA981264 CWA981299 ACXE24C00940 ACXE24C00950 ACXH13C00180 ACXA75C00450 ACXE10C02660 ACXE22C00760 CWE14C1112 CWD001385 XTT4+16CFJ ACXH52-00140 CWH851173 CWH361147 CWH82C1705 CWD00C1293 ACXF55-04100 ACXF55-04110 ACXF60-05670 ACXF60-05680 ACXF60-05690 ACXF60-05700 ACXF60-05710 ACXF60-05720 ACXF60-05730 ACXF60-05770 ACXF60-05750 ACXF60-05760 REMARK O O O O O O O O O (NOTE)  All parts are supplied from PAPAMY, Malaysia (Vendor Code: 00029488).  “O” marked parts are recommended to be kept in stock. 121 AMP Air Conditioning www. ampair. co. uk | sales@ampair. co. uk 20. 2 Outdoor Unit 20. 2. 1 I/I CU-TE20TKE CU-TE25TKE CU-TE35TKE 52 I/I 57 32 I/I 53 I/I 58 I/I 54 I/I 59 30 29 I/I 55 I/I 60 I/I 56 I/I 61 12 42 44 3 6 5 22 25 13 7 26 28 19 43 8 39 38 2 27 21 24 20 33 45 23 9 14 16 36 31 11 10 17 15 34 4 1 46 41 Note The above exploded view is for the purpose of parts disassembly and replacement. The non-numbered parts are not kept as standard service parts. [. . . ]