Mode d'emploi PANASONIC H98

[. . . ] SIMMC 0001002C1 E1 Service Manual Microwave Oven CPH Canada MODELS NN-S560BF/WF NN-S550BF/WF NN-S540BF/WF NN-L530BF NN-L530WF NN-L520WF NN-S510WF * RPH Model refer to the last page. APH USA Specifications for APH : Specifications: Power Source: Power Requirement: Output(IEC705-88): Microwave Frequency: Timer: Outside Dimensions: Oven Cavity Dimensions: Weight: Model: NN-S560BF/WF NN-S550BF/WF NN-S540BF/WF NN-L530BF/WF *120V AC Single Phase, 60Hz 1370W 1370W 1300W *2450MHz *99min. 99sec *20 ”(518mm)(W) *14 ”(375mm)(W) O 1370W 1100W 1370W 1000W 1300W 16 ”(407mm)(D) 15 ”(386mm)(D) O 11”(301mm)(H) 8 ”(225mm)(H) O O *26. 5 lbs. (12. 0kg) Output power:IEC705-88 Test Procedure Specifications subject to change without notice. Specifications for CPH: Specifications: Power Source: Power Requirement: Output(IEC705-88): Microwave Frequency: Timer: Outside Dimensions: Oven Cavity Dimensions: Weight: Model: NN-S560BF/WF NN-S540BF/WF NN-L530WF NN-L520WF NN-S510WF *120V AC Single Phase, 60Hz 1370W 1370W 1200W *2450MHz *99min. 99sec *20 ”(518mm)(W) *14 ”(375mm)(W) O 1370W 1100W 1370W 1100W 1370W 1000W 1100W 16 ”(407mm)(D) 15 ”(386mm)(D) O 11”(301mm)(H) 8 ”(225mm)(H) O O *26. 5 lbs. (12. 0kg) Output power:IEC705-88 Test Procedure Specifications subject to change without notice. [. . . ] (E) Remove 2 screws holding fan motor to orifice. (F) Separate the fan motor from the orifice assembly by freeing 2 catch hooks on the orifice assembly. - 13 - 5. Door assembly (A) Remove door C from door E by carefully pulling outward starting from upper right hand corner using a flat blade screwdriver. (B) Separate door E from tabs on door A and remove door A. (C) Open Door E at the opening angle of approximately 10° (Note: The door cannot be removed if the opening angle is greater than 10°). (D) Remove the door from its hinges by pushing the door’s lower hinge pin upward and out. (F) Remove door key and door key spring. (G) When reassembling door hold door E at the opening angle of approximately 10°. (H) Place the door’s lower hinge pin into the bottom hinge hole. (I) Use your left index finger to support the door’s lower hinge pin while guiding the door’s upper hinge pin into the top hinge hole. (J) Lower your finger to seat the door onto the hinges. If door is misaligned, apply pressure DOOR CCREEN B DOOR A DOOR KEY DOOR KEY SPRING DOOR C DOOR E BASE MOTOR COVER until alignment is achieved. After replacement of the defective component parts of the door, reassemble, install, and perform microwave leakage test. Turntable motor (A) Remove the motor cover by breaking off at the 8 spots indicated by arrows with a cutter or the like. (See Figure) NOTE: After breaking off the motor cover, make sure that cut-off portions are properly trimmed off or bend to inside so that no sharp edge will expose to outside. (B) Disconnect 2 lead wires connected to the turntable motor. (C) Remove the turntable motor by removing 1 screw. NOTE: After reinstalling the new turntable motor and reconnecting the two lead wires, reinstall the motor cover by rotating it around 180 , tucking the tabs under the base into the 2 provided slots, then screw the single tab to the base using a 4mm X 6mm screw (not provided). Steam Sensor (A) Remove 1 screw holding steam sensor unit. (indicated by arrows) (B) Disconnect CN2 connector from digital programmer circuit board. (C) Remove exhaust guide from steam sensor unit. (D) Remove catch hooks on sensor mounting plate and air guide. [. . . ] Inverter (U) (SEE NOTE) NOTE: After check, unplug unit to reset to normal operation mode. Alternate way to troubleshoot oven with AC Ampere meter used H97, H98, H99 appears in display window a short time after start key is pressed and no microwave oscillation with AC Ampere meter used for troubleshooting H97, H98, or H99 appears in display window NOTE: DO NOT try to repair this Inverter Power Supply (U) and also DO NOT Check oven input AC amperes measure at oven plug more than 1A Check magnetron filament continuity OK Open 0. 4-0. 8A DPC board Loose wiring RE-ADJUST PRESET VOLUME on the board. It is very dangerous to repair or adjust without sufficient test equipment because this circuit handles very high voltage and very large current. Off alignment of inverter board operation is dangerous. Operating a misaligned Inverter circuit is dangerous due to the very high voltage and current that is produced by this board. [. . . ]