Mode d'emploi PANASONIC SA-XR70

[. . . ] Dear customer Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. Operating Instructions SA-XR70 Table of contents Before use IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Listening caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The default level is 3. EFFECT ­ w + q Select "C-IMG". You can adjust the sound field by adjusting the level of the speakers and effect. These adjustments can be made for each SFC mode. To adjust the speaker level LEVEL ­ w + q To adjust SFC effect EFFECT Select speaker channel. Adjust the level. C, RS, SB and LS: ­10 dB to +10 dB SW: ­ ­ ­ (off) MIN 1 ­ 19 MAX Adjust the effect. SFC effect can be adjusted between EFFECT 1 (minimum) and EFFECT 10 (maximum). The factory setting is EFFECT 5 for each mode. C RS LS SW When 6. 1CH DECODING is on: C RS SB LS SW Output is only from the speakers selected in the speaker settings. Listening to multi-channel source in stereo (2CH MIX mode) When multi-channel sources are played in this mode, the sounds intended for the other speaker channels are played through the front speakers. STEREO/ 2CH MIX OFF · To cancel: Press [STEREO/2CH MIX, OFF]. If the unit does not automatically recognize Dolby Digital Surround EX or DTS-ES and output is 5. 1 channels: Press [6. 1CH DECODING] to switch the mode on manually. Sound will now come from the surround back speaker. The 6. 1CH DECODING mode cannot be used when the following input signals are supplied: · When only the center channel signals are input. Notes on sound modes Dolby Pro Logic x, Dolby Pro Logic , DTS NEO:6 and SFC modes remain in effect until you change them. · To cancel : Press [STEREO/2CH MIX, OFF]. The 2CH MIX mode remains in effect until you change input mode or turn off the unit. · To return to surround sound: Press [STEREO/2CH MIX, OFF]. When input is PCM with sampling frequencies of 192, 176. 4 (COAXIAL1, HDMI), 96, or 88. 2 kHz: · You cannot add surround effects with Dolby Pro Logic x, Dolby Pro Logic , DTS NEO:6 or SFC. When neither the center nor surround speakers are selected in the speaker settings: · You cannot use Dolby Pro Logic x, Dolby Pro Logic , DTS NEO:6 or SFC. When the surround back speaker is not selected in the speaker settings: · You cannot use 6. 1CH DECODING mode. Notes on HDMI When the input signal is multi-channel DVD-Audio: · Speaker settings are ineffective. The speaker settings selected on this unit need to be set on the DVD player or DVD recorder. · You cannot use Dolby Pro Logic x, Dolby Pro Logic , DTS NEO:6 or SFC. · You cannot use 6. 1CH DECODING mode. With a source for which down-mixing is prohibited: · The 2CH MIX mode cannot be used. · Play may not be normal if SPEAKERS B has been selected or all the speakers have been set to off and you are listening through headphones. RQT7523 Step 4 17 ­ w + q Control guide Main unit Standby indicator [^] When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on. [SPEAKERS, A, B, BI-WIRE] For selecting speakers A or B. To use BI-WIRE, press [A] and [B] at the same time. Turning the speakers off automatically engages the STEREO/2CH MIX mode (when listening through headphones, for example). [% DIGITAL, % EX/PL x, % PL , DTS 96/24, DTS-ES, DTS, DTS NEO:6] Lights to indicate the source's input signal and decoding format used. [. . . ] Check the settings of the connected equipment. Should anything unusual happen using a HDMI connection: - Turn the connected equipment on again. - Pull out the HDMI cable then reinsert it. - Reduce the amount of equipment connected in series to the HDMI terminal if exceeding 2 units. [. . . ]