Mode d'emploi PHILIPS E1205

[. . . ] • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can't hear what's around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headphones can cause hearing loss. [. . . ] Make sure that the mobile phone is turned on and its Bluetooth feature is activated. Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone. Tip  Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3. 0 or higher, no need to enter a password Connect the supplied USB charging cable to the charging slot on the headphones and the charger/USB port of a computer. LED turns white during charging and turns off when the headphones is fully charged. Tip  Normally, a full charge takes 2 hours. 4 Use your headphone Connect the headphone to your Bluetooth device Turn on your mobile phone/ Bluetooth device. Press and hold the on/off button (>2s) to turn the headphones on. The headphones are reconnected to the last connected device automatically. If the last one is not available, the headphones try to reconnect to the second last connected device. Manage your calls and music On/off Task Power on Button On/off, music/call control On/off, music/call control Operation Press and hold (>2s) Press and hold (>4s) Power off Music control Task Play or pause music. Adjust volume Next track Previous track Call control Task Pick up/ hang up a call. Reject a call Button On/off, music/ call control On/off, music/ call control Operation Press once. Operation Button On/off, Press once music/call control Press once Press twice Press twice Tip  If you turn on the mobile phone or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone manually.  If the headphones fail to connect to any Bluetooth device within range in 5 minutes, it will switch off automatically to save the battery life. Press and hold (>2s) Trigger voice assistant (Android/iOS) Task Trigger voice assistant Button Operation On/off, Press twice music/call control Factory Reset Task Factory reset Button Operation Volume + Press and hold and together (>4s) Summary of LED indicator Headphones status The headphones are connected to a mobile phone. Indicator The blue LED flashes for every 5 seconds. The headphones The blue LED are disconnected flashes for to a mobile phone every 10 seconds. The headphones The LED flashes are ready for blue and white pairing. White LED double flashes Trigger once in 60 seconds. The white LED turns on until battery is fully charged. Charging 5 Technical data Music time: 7 hours Talk time: 5 hours Standby time: 60 hours Normal time for a full charge: 2 hours Battery: Rechargeable lithium polymer battery (100 mAh) Bluetooth version: 5. 1 Compatible Bluetooth profiles: Bluetooth profile: HSP, HFP, A2DP, AVRCP Operating range: Up to 10 meters (33 feet) Speaker driver: 8 mm Transmitter power: < 10 dBm Frequency response: 20 – 20kHz Impedance: 32 ohm Sensitivity: 108. 5db/1mW/1000Hz Distortion: <3%@1kHz THD Maximum power input: 5mW USB-C port for charging Low battery warning: available Note  Specifications are subject to change without notice. 6 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www. p4c. philips. com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones. • Make sure the headphone is disconnected from the charging case before removing the battery. Disposal of your old product and battery Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. [. . . ] This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device. [. . . ]