Mode d'emploi PHILIPS SB500A

[. . . ] You can find the Declaration of Conformity on www. philips. com/support. • • • • • • Only use attachments or accessories specified by the manufacturer. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. Do not place any sources of danger on the speaker (e. g. The speaker can meet IPX7 waterproof standard only when the USB/AUDIO IN socket cover is covered seamlessly. [. . . ] e • Turn the shoq mode on or off. • Select different LED light patterns. • Charge the built-in battery. Overview of the speaker f g AUDIO IN • Connect an external audio device. a • • • • Turn the speaker on or off. Turn off the low battery indication. b • Enter Bluetooth pairing mode. • Clear Bluetooth pairing information. • In Bluetooth mode, press to pause or resume play. • In Bluetooth mode, press twice to play the next track. • Respond to an incoming call through Bluetooth connection. c 4 EN 3 Get started Always follow the instructions in this chapter in sequence. Charge the built-in battery Note •• It takes you approximately 3. 5 hours to fully •• The micro USB socket is for charging only. •• Rechargeable battery has a limited number charge the battery. Check the battery level The speaker is powered by the built-in rechargeable battery. • To check the battery level, press . »» The different behavior of the five LEDs indicates different battery levels. of charge cycles. Battery life and number of charge cycles vary by use and settings. When the battery level is low, LED 3 flashes red as illustrated. To turn off the low power indication, press . LED indication: LED 5 LED 5 LED 3 LED 1 Battery power Full > 80% 60% 80% 40% 60% 20% 40% Low battery (<20%) LED 1 LED 4 LED 2 LED 2 LED 3 LED 4 LED 5 LED 3 LED 1 LED 4 LED 2 Solid green Solid green Solid green Solid green Solid green Flash red Off Off Off Off Off To charge the built-in battery: • Connect the speaker to AC power by using a power adaptor (not supplied; 5V 2. 1A adaptor recommended). EN 5 System Battery status status System behavior Turn on/off On Being charged Beep once, without charging indication. Shows the charging indication All LEDs are on, then turn off in 3 minutes. • To turn the speaker on, press and hold for over two seconds until the LEDs light up. To turn the speaker off, press and hold for two seconds again. Note •• The speaker turns off automatically when being idle for 15 minutes. Off Being charged Fully charged Off Check the charging progress During charging, you can press check the charging progress. Battery level <20% charged 20% - 40% charged 40% - 60% charged 60% - 80% charged > 80% charged Fully charged to • LED 1 LED 2 LED 3 LED 4 LED 5 Flash Off green Solid Flash Off green green Solid green Flash Off green Flash Off green Flash green Solid green Solid green Solid green (turn off in 3 minutes) 6 EN 4 Play from Bluetooth devices With this speaker, you can listen to audio from Bluetooth-enabled devices and control the incoming call through Bluetooth. 2 3 On your Bluetooth device, enable Bluetooth and search for Bluetooth devices that can be paired (see the user manual of the device). Select [Philips SB500] displayed on your device for pairing. If necessary, input “0000” as the pairing password. »» After successful connection, the speaker beeps twice, and the blue LED light stops flashing. Connect a Bluetooth device Note enabled on your device, and your device is set as visible to all other Bluetooth devices. •• Any obstacle between this speaker and a Bluetooth device can reduce the operational range. [. . . ] • Press repeatedly to select a lighting effect or turn off the LED light: • Pattern 1 • Pattern 2 • Turn off Note •• If there is no music playback, the lighting effect will not start. Open the protective cover on the back of the speaker. Connect an audio input cable (not supplied) with a 3. 5 mm connector on both ends to • the AUDIO IN socket on this speaker, and • the headphone socket on the external device. Play audio on the external device (refer to its user manual). 3 EN 9 Adjust volume During music playback, press -/+ to increase or decrease volume. Tip •• You can press and hold -/+ to increase or •• When the volume reaches the maximum, decrease volume continuously. 6 Specif­ications Note •• Product information is subject to change without prior notice. • • • • • • • • • • • • • • • the speaker beeps twice. •• During Bluetooth playback, the volume control will be synchronized between the speaker and your Bluetooth device as long as your device supports this function. Rated output power (Amplifier): 2x15W RMS ≤ 1% THD Acoustic frequency response: 50-20000 Hz Speaker driver: 2 x 2” full range, 4 Ω Bass enhancement: 2 x 2. 5” passive radiator Bluetooth version: V2. 1 + EDR Bluetooth supported profiles: HFP V1. 6, A2DP V1. 2, AVRCP V1. 4 Bluetooth frequency band / Output power: 2. 402GHz ~ 2. 480GHz ISM Band / ≤ 4dBm (Class 2) AUX input level: 500mV±100mV Water resistance: IPX7 Built-in battery: Li-ion battery (7. 4 V, 2200 mAh) Play time in battery mode: Approx. [. . . ]