Mode d'emploi SAMSUNG SF 3100

[. . . ] InkJet Facsimile User Guide SF-3100/SF-3100T Please read this guide before you use this equipment. Downloaded from www. Manualslib. com manuals search engine ELECTRONICS Visit us at: http://www. samsungelectronics. com If you have access to this online service, you can download the User’s Guide and drivers from Samsung Electronics. P/N : JB68-00228A Rev. 1. 00 Downloaded from www. Manualslib. com manuals search engine Important Precautions and Safety Information When using this fax machine, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and injury to persons: 1. Use common sense whenever operating electrical appliances. Follow all warnings and instructions marked on the product and in the literature accompanying the product. [. . . ] To learn about Remote Commands, see “Using Remote Commands” on page 4-9. If there is no key input or the wrong password is entered while the machine sends out beeps, and the line will be disconnected. Chapter 4 4-7 Downloaded from www. Manualslib. com manuals search engine The Answering Machine Using the Answering Machine from a Remote Phone You don’t need to be at the machine’s Control Panel to operate the answering machine. If you have access to a Touch-Tone phone, you can operate many features, such as message playback, regardless of where you are. To operate your machine from a remote phone, you need to enter a five-character: Remote Password. The Remote Password is preset at the factory to ‘#139#’ and you can change the password to any number you want, through the User Options. For more information, see “TAM Options (SF3100T only)” on page 6-11. Accessing the Machine 1 Place a call to your fax machine from a TouchTone phone. •A pulse line works only if you can manually switch the phone to tone dialling. If you can, switch it to tone after you dial the fax number but before you enter any Remote Password or Remote Command. 2 Enter your Remote Password when the machine answers with the greeting. •When the correct password is recognized by the machine, you will hear two short beeps (the confirmation tone). •If the machine doesn’t immediately respond to a remote password: - try to enter the code again. - If the machine does not accept and you think you entered the password correctly, press and hold each key at least for a second - try to enter the code after TAM message - If the problem persists, try again from another phone. 4-8 Downloaded from www. Manualslib. com manuals search engine The Answering Machine 3 Enter the Remote Command corresponding to the operation within ten seconds. •When the specified operation is complete, you hear a short beep. You can then enter another command for another operation. If you enter a remote code while the machine is responding to your command, the unit stops the current operation and performs new operation. For the Remote Commands, "Using Remote Commands" below. 4 Using Remote Commands Code #0 #1 #2 #3 #4 #5 #6 #7 #8 #9 #✽1 #✽2 Exits remote control mode. Press #0 to finish the remote session. Important: if you don’t enter ‘#0’, your machine might not hang up for several minutes. The chart below describes which Remote Code you have to enter for remote operation: Operation Changes the greeting message. After entering the command, speak into the handset. If you run out of recording time, the machine stops and plays back the message. The machine beeps and plays all messages. If there are no messages, the machine beeps four times and waits for another command to be entered. Stops the ICM play and waits for remote code when playing ICMs (#2, #5). The machine skips the current message and plays the previous one. The machine beeps and plays all new messages. If there are no new messages, the machine beeps four times and waits for another command to be entered. The machine skips the current message and plays the next one. [. . . ] To load Letter, or Legal-size paper, you have to set ‘PAPER SIZE’ option via the Setting User Options. To change it, see “System Setup Options” on page 6-8 in the User’s Guide. 9 Downloaded from www. Manualslib. com manuals search engine Installation Installing Print Cartridge When the machine is powered up without the print cartridge installed, the LCD displays ‘NO CARTRIDGE ’. 1 2 3 Press Setup. The display shows ‘CHANGE CARTRIDGE’ Press (Start/Enter). Open the Control Panel (➀) and the Cartridge Compartment Cover (➁) with your hand. ➁ Cartridge Compartment cover ➀Control panel 4 Remove the new print cartridge from its packaging. [. . . ]