Mode d'emploi TRENDNET TEW-644UB

[. . . ] -- Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Make sure the environment has minimal interference and obstructions. Connecting the USB Extension Cable The USB extension cradle that comes with the Adapter has Type A connectors on both ends. One end of the cradle is a male Type A connector that plugs into the PC's USB port. The other end of the cradle is a female Type A connector that plugs into the Adapter. This USB extension cradle can be adjusted to improve the wireless connection. The SSID must be identical for each client in the wireless network. Wireless Mode: There are two modes available for selection Infrastructure ­ to establish wireless communication with the LAN and other wireless clients through the use of Access Points. Ad-Hoc ­ to establish point-to-point wireless communication directly with other wireless client devices. Authentication: The following options are available: Open System, Shared Key, WPA-PSK, WPA2-PSK, WPA EAP-TLS, WPA2 EPA-TLS. Select Open System, Shared Key for WEP data encryption feature. 6 Open System and Shared Key Open System and Shared Key requires the user to set a WEP key to exchange data with other wireless clients that have the same WEP key. The following will be activated when Open, Shared Key or Auto is enabled: Default Key: select one of the 4 keys to use. Network Key: choose the encryption way, either in HEX or ASCII formats, and enter the password in the blank space. Key Length: select 64 or 128 bits as the length of the keys Key Format: ASCII or HEX 7 WPA/WPA2 EAP-TLS If using the WPA/WPA2 EAP-TLS authentication method, please select the Encryption type for TKIP or AES then select the WPA/WPA2 Certificate from drop down list. 8 WPA/WPA2-PSK If using the WPA-PSK/WPA2-PSK authentication method, please select the Encryption type for TKIP or AES then enter the Passphrase key. 9 Site Survey This screen allows the user to scan for available wireless networks (wireless clients and Access Points). It also allows the user to establish wireless communications with an available wireless network. Select any one of the wireless networks by double-clicking on it or clicking on the "Connect" button. Click the "Refresh" button to scan for available networks. 10 Profile The user can create and manage the created profiles for home, work or public areas. By double-clicking on one of the created profile, the setting will adjust to the specific setting such as SSID, channel, and encryption as saved by that particular profile. 11 Add: Adds a new profile. Enter the Profile Name, SSID and select the Wireless Mode, Authentication and Encryption then click Apply to save the new profile. Remove: Delete the selected profile. 12 Edit: Edit an exist profile. Edit the SSID and select the Wireless Mode, Authentication and Encryption then click Apply to save the profile. When the Profile name was changed, a new profile will be added in the list. Connect: Selected a profile from list then click the Connect to connecting to the wireless network with the profile setting. 13 WPS Wi-Fi Protected Setup (WPS) is an optional certification program from the Wi-Fi Alliance that is designed to ease the task of setting up and configuring security on a wireless network. There are two methods used in the WPS as below instruction. Push the button on my access point Using the WPS configuration with the "Push the button on my access point" method, the configuration steps as below: 1) Selected the "Push the button on my access point". 2) Push the WPS configuration button on your wireless access point or router. 3) Cliek the Next button start the WPS configuration. 14 4) If the WPS configuration was successful, the follow window will show on. 5) If the WPS configuration was failed, the follow window will show on. 15 Enter a PIN into my access point Using the WPS configuration with the "Enter a PIN into my access point" method, the configuration steps as below: 1) Selected the "Enter a PIN into my access point", the PIN will be show on the button of the windows. 2) Enter the PIN code into the WPS "Clint PIN number" of you wireless access point or router then click the Start PIN button, the wireless access point or router will start the WPS configuration process. 16 3) Selected a wireless access point or router which one will be connecting then click the Next button start the WPS configuration. If the "Automatically select the network" was checked, the setup step will be skip. 17 4) If the WPS configuration was successful, the follow window will show on. 5) If the WPS configuration was failed, the follow window will show on. 18 About This screen displays information about the Wireless N USB Adapter, such as the Driver and Utility version. [. . . ] If the WPS configuration was successful, the follow window will show on. 4. If the WPS configuration was failed, the follow window will show on. Using the WPS configuration with the "PIN" method, the configuration steps as below: 31 1. Enter the PIN code into the WPS "Clint PIN number" of you wireless access point or router then click the Start PIN button, the wireless access point or router will start the WPS configuration process. 2. Selected a wireless access point or router which one will be connecting then click the PIN button start the WPS configuration. [. . . ]